Книжкові видання та компакт-диски Журнали та продовжувані видання Автореферати дисертацій Реферативна база даних Наукова періодика України Тематичний навігатор Авторитетний файл імен осіб
|
Для швидкої роботи та реалізації всіх функціональних можливостей пошукової системи використовуйте браузер "Mozilla Firefox" |
|
|
Повнотекстовий пошук
Пошуковий запит: (<.>A=Fröhlich T$<.>) |
Загальна кількість знайдених документів : 6
Представлено документи з 1 до 6
|
1. |
Fröhlich T. Calibration bench for heat flux sensors [Електронний ресурс] / T. Fröhlich, M. Hohmann, M. Schalles // Journal of thermoelectricity. - 2015. - № 1. - С. 49-59. - Режим доступу: http://nbuv.gov.ua/UJRN/jtherel_2015_1_8
| 2. |
Yatsyshyn S. Development of software and hardware for the method of rehabilitation of patients with obliteration of atherosclerosis of the limb vessels [Електронний ресурс] / S. Yatsyshyn, B. Stadnyk, Yu. Khoma, M. Mykyichuk, D. Mihunov, Th. Fröhlich, R. Mastylo // Вимірювальна техніка та метрологія . - 2019. - Т. 80, Вип. 1. - С. 24-26. - Режим доступу: http://nbuv.gov.ua/UJRN/metrolog_2019_80_1_7
| 3. |
Augustin S. Challenges of temperature measurement during the friction stir welding process [Електронний ресурс] / S. Augustin, T. Fröhlich, G. Krapf, J. Bergmann, M. Grätzel, J. Gerken, K. Schmidt // Measuring equipment and metrology. - 2020. - Vol. 81, № 1. - С. 34-38. - Режим доступу: http://nbuv.gov.ua/UJRN/metrolog_2020_81_1_8 The exact determination of the process zone temperature can be considered as an increasingly important role in the control and monitoring of the friction stir welding process (FSW). At present, temperature measurement is carried out with the aid of a temperature sensor integrated into the tool (usually thermocouples). Since these cannot be attached directly to the joining area, heat dissipation within the tool and to the environment cause measurement deviations as well as a time delay in the temperature measurement. The article describes a process and the challenges that arise in this process, how a direct temperature measurement during the process can be achieved by exploiting the thermoelectric effect between tool and workpiece, without changing the tool by introducing additional temperature sensors.
| 4. |
Stadnyk B. Calibration of measuring channels of non-dismantling cyber-physical systems [Електронний ресурс] / B. Stadnyk, V. Yatsuk, M. Mykyichuk, S. Yatsyshyn, T. Fröhlich, R. Mastylo // Вимірювальна техніка та метрологія. - 2021. - Т. 82, Вип. 3. - С. 12-17. - Режим доступу: http://nbuv.gov.ua/UJRN/metrolog_2021_82_3_4 The analysis of the concept of Open-Science Space is carried out. The existence of ways to achieve reproducibility and traceability of research results performed by a group of worldwide situated cyber-physical system operators/supervisors is shown. Ways to ensure the efficient operation of cyber-physical systems as complex technological nondemountable objects with high requirements for metrological characteristics have been studied. To develop the scattered cyberphysical systems, the portable stable-in-time code-controlled measures of physical quantities have been studied. They have to be metrologically confirmed in the laboratory before the delivery to the site of the measuring subsystem for its calibration.
| 5. |
Blumröder U. Frequency comb-coupled metrology lasers for nanopositioning and nanomeasuring machines [Електронний ресурс] / U. Blumröder, R. Füßl, T. Fröhlich, E. Manske, R. Mastylo // Вимірювальна техніка та метрологія. - 2021. - Т. 82, Вип. 4. - С. 36-42. - Режим доступу: http://nbuv.gov.ua/UJRN/metrolog_2021_82_4_9
| 6. |
Stadnyk B. Mass Measures with Coded Remote Access for Cyber-Physical Systems [Електронний ресурс] / B. Stadnyk, T. Fröhlich, M. Mykyychuk, I. Klos, S. Yatshyshyn, I. Kalinovska // Advances in cyber-physical systems. - 2017. - Vol. 2, Num. 2. - С. 77-80. - Режим доступу: http://nbuv.gov.ua/UJRN/advcyphsys_2017_2_2_8 The aspects of design and operation of information measuring subsystem of Cyber-Physical System of coke and chemical plant are considered. This subsystem of mass parameters definition, based on industrial internet, provides coded remote access aiming at the execution of both weighing and verification metrological operations by using an embedded multivalued mass measure. To ensure the quality and reproducibility of Cyber-Physical System a remote access on the basis of TCP/IP protocol to balances was studied and developed. Installation was equipped with the standard built-in mass measure that enabled to perform in-place operations of metrological checking, verification, calibration etc. not interrupting the production cycle.
|
|
|